| Customization: | Available |
|---|---|
| After-sales Service: | Online Services |
| Warranty: | One Year |
|
Still deciding? Get samples of US$ 25/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Drive Rods and Pony Rods are manufactured from micro-alloyed, modified special quality hot rolled carbon or alloy steel. Bar and sucker rod dimensions and tolerances conform to API Spec 11B, latest edition, and AISI Steel Products Manual. It is used to connect the pumping unit on the ground and PCP. Sucker rod is an important part in the oil production system. Different grades of sucker rod has features of high strength, non-corrosive medium, good tensile and long service life.
Sucker Rods, Drive Rods and Pony Rods are manufactured from micro-alloyed, modified special quality hot rolled carbon or alloy steel. Bar and sucker rod dimensions and tolerances conform to API Spec 11B, latest edition, and AISI Steel Products Manual.
Sucker rods are available in 5/8" (15.88 mm), 3/4" (19.05 mm), 7/8" (22.23 mm), 1" (25.40 mm) and 1 1/8" (28.58 mm).
Drive Rods for Progressing Cavity Pump application are available in 1" (25.40 mm), 1 1/4" (31.75 mm), and 1 1/2" (38.10 mm) body diameter and in 25' (7.62 m) lengths.
1. All rods are straightened and inspected by Eddy Current/magnetic for surface defects.
2. Both ends are upset by automatic high-speed hot forging. Rods are full length normalized to relieve residual stresses, air-quenched, and tempered to refine and homogenize grain structure, and surface nor peened to remove any remaining heat treat scale.
3. All rods are also nor peened to improve fatigue life. Upset pin blanks are machined and dimensions gauged. Pin threads are cold-formed to strengthen the thread from fatigue.
4. An inhibitor-lubricant is applied to each pin and thread protector installed.
5. An oil soluble coating protects rods from atmospheric corrosion in storage.
6. All rods are bundled to prevent handling damage duringtransportation to the well location.
7. Quality control inspections are performed at each step of the manufacturing process.
Sucker Rod & Pony Rod
| Sucker Rod Nominal Value (mm) | Sucker Rod Nominal Value | Rod Body diameter | Pin Size | Pin Size | Shoulder OD | Shoulder OD | Wrench Square width | Wrench Square Length | API sucker rod length with coupling (mm/ft) |
| (in) | (mm) | (in) | (mm) | (in) | (mm) | (mm /in) | (mm /in) | ||
| 16 | 5/8 | 15.88 | 15/16 | 23.81 | 1.25 | 31.8 | 22.2(0.875) | 31.8(1.250) | 609.2 (2') |
| 1219 (4') | |||||||||
| 1828 (6') | |||||||||
| 19 | 3/4 | 19.05 | 2001/1/16 | 26.99 | 1.5 | 38.1 | 25.4(1.000) | 2438 (8') | |
| 22 | 7/8 | 22.23 | 2001/3/16 | 30.16 | 1.625 | 41.3 | 25.4(1.000) | 3048 (10') | |
| 25 | 1 | 25.4 | 2001/3/8 | 34.93 | 2 | 50.8 | 33.3(1.313) | 7620 (25') | |
| 29 | 2001/1/8 | 28.58 | 2001/9/16 | 39.69 | 2.25 | 57.2 | 38.1(1.500) | 9144 (30') |
Drive Rod & Pony Rod
| Sucker Rod Nominal Value (mm) | Sucker Rod Nominal Value | Rod Body diameter | Rod End Size | Rod End Size | Length of Finished Product (mm) | Length of Finished Product (ft) |
| (in) | (mm) | (in) | (mm) | |||
| 25 | 1 | 25.4 | 7/8 | 22.23 | 1000 | 2 |
| 2000 | 4 | |||||
| 29 | 2001/1/8 | 28.58 | 1 | 25.4 | 3000 | 6 |
| 32 | 2001/1/4 | 31.75 | 1 | 25.4 | 7620 | 25 |
| 38 | 2001/1/2 | 38.1 | 2001/1/8 | 28.58 | 8000 | 26 |
Mechannical Propterty
| Grade | Tensile strength MPa | Yield strength MPa | Percentage elongation % | Contraction percentage of area % | |
| C | 620 - 795 | ≥ 415 | ≥ 13 | ≥ 50 | Scuker rod |
| K | 620 - 795 | ≥ 415 | ≥ 13 | ≥ 60 | Scuker rod |
| D | 795 - 965 | ≥ 590 | ≥ 10 | ≥ 50 | Scuker rod & Drive Rod |
| KD | 795 - 965 | ≥ 590 | ≥ 10 | ≥ 50 | Scuker rod & Drive Rod |
| HL | 965 - 1195 | ≥ 795 | ≥ 10 | ≥ 45 | Scuker rod & Drive Rod |
| HY | 965 - 1195 | N/M | N/M | N/M | Scuker rod & Drive Rod |
Chemical Composition of Common Sucker Rod Material
| AISI | C | Si | Mn | P | S | Cr | Ni | Mo | V | Cu | Al |
| 1541 | 0.36-0.45 | 0.15-0.35 | 1.35-1.65 | ≤0.04 | ≤0.04 | ≤0.3 | ≤0.35 | ≤0.06 | 0.04-0.09 | ≤0.35 | ≤0.035 |
| 4120 | 0.17-0.24 | 0.17-0.37 | 0.4-0.7 | ≤0.025 | ≤0.025 | 0.8-1.1 | ≤0.3 | 0.15-0.25 | / | ≤0.2 | / |
| 4130 | 0.26-0.33 | 0.17-0.37 | 0.4-0.7 | ≤0.025 | ≤0.025 | 0.8-1.1 | ≤0.3 | 0.15-0.25 | / | ≤0.2 | / |
| 4138 | 0.37-0.45 | 0.17-0.37 | 0.9-1.2 | ≤0.025 | ≤0.025 | 0.9-1.2 | ≤0.3 | 0.2-0.3 | / | ≤0.2 | / |
| 4138M | 0.37-0.45 | 0.17-0.37 | 0.9-1.2 | ≤0.025 | ≤0.025 | 0.9-1.2 | ≤0.3 | 0.2-0.3 | 0.04-0.09 | ≤0.2 | / |
| 4140 | 0.38-0.45 | 0.17-0.37 | 0.5-0.8 | ≤0.025 | ≤0.025 | 0.9-1.2 | ≤0.3 | 0.15-0.25 | 0.04-0.09 | ≤0.2 | / |
| 4142 | 0.38-0.45 | 0.17-0.37 | 0.5-0.8 | ≤0.025 | ≤0.025 | 0.9-1.2 | ≤0.3 | 0.15-0.25 | 0.04-0.09 | ≤0.2 | / |
| 3130 | 0.22-0.29 | 0.15-0.35 | 0.71-1.0 | ≤0.025 | ≤0.025 | 0.42-0.65 | 0.72-1.0 | 0.01-0.06 | / | ≤0.2 | / |
| 4320 | 0.18-0.42 | 0.15-0.35 | 0.8-1.0 | ≤0.025 | ≤0.025 | 0.7-0.9 | 1.15-1.5 | 0.2-0.3 | 0.04-0.09 | ≤0.35 | ≤0.035 |
| 4330 | 0.3-0.35 | 0.15-0.35 | 0.8-1.1 | ≤0.025 | ≤0.025 | 0.8-1.1 | 1.65-2.0 | 0.2-0.3 | 0.05-0.10 | ≤0.2 | / |
| 4621 | 0.18-0.23 | 0.17-0.37 | 0.7-0.9 | ≤0.025 | ≤0.025 | ≤0.35 | 1.65-2.0 | 0.2-0.3 | / | ≤0.2 | / |
| 4720 | 0.19-0.23 | 0.15-0.35 | 0.85-1.05 | ≤0.025 | ≤0.025 | 0.8-1.05 | 0.9-1.2 | 0.22-0.30 | 0.02-0.05 | 0.40-0.60 | / |
1) How can I place an order?
A: You can contact us by email about your order details, or place an order online.
2) How can I pay you?
A: After you confirm our PI, we will request you to pay. T/T and Western Union are the most usual ways we are used.
3) What's the order procedure?
A: First we discuss order details and production details by email or TM. Then we issue you a PI for your confirmation. You will be requested to do a prepaid full payment or deposit before we go into production. After we get the deposit, we start to process the order. We usually need 15-25days if we don't have the items in stock. Before production has finished, we will contact you for shipment details, and the balance payment. After payment has been settled, we start to prepare the shipment for you.
4)How do you take care when your clients received defective products?
A: replacement. If there are some defective items, we usually credit them to our customer or replace them in the next shipment.
5)How do you check all the goods in the production line?
A: We have spot inspection and finished product inspection. We check the goods when they go into the next step production procedure.
){kind=link}